top of page

Chop-N-Feed Bucket

ProDig Beet Chopper and Meal Feeding Bucket is available in three sizes from 2m to 2.5m which will suit tractor loaders, telehandlers, articulated loaders & Tractor 3 Point Linkage. This versatile unit is equipped with a hydraulic motor which drives a heavy-duty auger for both chopping and feeding out so there is no need for a PTO drive. The large output on the bucket allows the bucket to unload and chop in a minimal amount of time.

​

  • Auger mover is fitted on the rear of the bucket rather than the side to allow use in close proximity with walls.

  • Easy access to all moving parts

  • Heavy duty buckets construction to allow for use on all machines.

  • Bolt on hitch system mean the bucket can be mounted off centred if required.

  • Hardened cutting edge and leading edge

  • Available with bolt on hitch system to fit all machines

  • Option of right or left-hand side chopping.

  • Four minutes per cubic meter chop rate

General Purpose Loader Bucket

Tele-Handler/Artic loader buckets available in capacity from 0.8m³ to 1.7m³.

​

  • Designed for general use such as loading, re-handling etc.

  • Manufactured with S275 structural grade plate and 120x60 box section.

  • Pressed steel curved shell retains less material when emptied.

  • Hardened 150mm x 20mm and 200 x 25 steel cutting edge as standard.

  • 10mm straps around shell for superior structural integrity.

  • Weld on hitch brackets on all buckets.

Grain Bucket

Grain buckets available in capacity from 1.9m³ to 3.6m³.

​

  • Designed to handle bulk materials such as grain, wood-chip etc.

  • Pressed steel curved shell retains less material when emptied.

  • Hardened 250mm x 30mm steel cutting edge as standard.

  • 12mm wear straps for superior structural integrity.

  • Side wear strips and top deflector as standard.

  • Crowd back to water level on most machines.

Hi-Tip Bucket

Available in a range of sizes from 0.85m³ up to 6.0 m³.

​

  • Discharge height and forward reach increased by 1400mm & 600mm respectively.

  • For use with various materials such as gravel, grain, woodchips, compost, etc.

  • Soft close twin double acting hydraulic rams that are protected within double skin sides.

  • Flat floor for easy loading, with 400 Brinell steel cutting edge.

  • Can be fitted with optional 400 Brinell bolt on reversible cutting edge.

  • High yield alloy steel used in the carriage frame for a longer working life.

  • Designed with water level crowd-back to retain more material.

  • Deflector plate to prevent spillage onto the loader hitch.

  • Weld on or bolt on hitch brackets to suit any machine type.

Skid Steer Hi-Tip Bucket

Available in a range of sizes from 0.65m3(1.5M) up to 0.85 m3(2.0M).

 

  • Discharge height and forward reach increased.

  • For use with various materials such as gravel, grain, wood chips, compost, etc.

  • Soft close twin double acting hydraulic rams that are protected within double skin sides.

  • Flat floor for easy loading, with 400 Brinell steel cutting edge.

  • Can be fitted with optional 400 Brinell bolt on reversible cutting edge.

  • High yield alloy steel used in the carriage frame for a longer working life.

  • Designed with a low back for better vision and side access steps for safety.

Telehandler Grapple Bucket

Hydraulic grapples can be fitted to all of our GP range of Tele/Artic loader buckets.

​

  • Ideal for efficient handling of maize, manure, recycling etc. on Wheel Loader or Tele-Handler.

  • Capacity of bucket increased by 40% when handling waste/recycling materials.

  • Heavy duty 8mm wall box section, and 10mm plate in grapple construction.

  • 25mm thick curved profiled Hardox tines welded through box section.

  • Twin double acting hydraulic rams are mounted the top of the bucket for extra downward force.

  • All moving parts fitted with greasing points.

  • Available with optional bolt in cut away sides.

  • Not suitable for pit silage.

Tractor Grapple Bucket

Hydraulic grapples can be fitted to all of our GPT range of Tractor loader buckets.

​

  • Ideal for efficient handling of maize, manure, recycling etc. on Tractor Loaders.

  • Capacity of bucket increased by 40% when handling waste/recycling materials.

  • Heavy duty 8mm wall box section, and 10mm plate in grapple construction.

  • 25mm thick curved profiled Hardox tines welded through box section.

  • Twin double acting hydraulic rams are mounted the top of the bucket for extra downward force.

  • All moving parts fitted with greasing points.

  • Available with optional bolt in cut away sides.

  • Not suitable for pit silage.

Tractor Loader Bucket

Tractor loader buckets available in widths from 1.5m to 2.5m.

​

  • Manufactured with S275 structural grade plate and 120x60 box section.

  • Pressed steel curved shell retains less material when emptied.

  • Hardened 150mm x 16mm steel cutting edge as standard.

  • 8mm straps around shell for superior structural integrity. 

bottom of page